主營產品
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
HONEYWELL ACX633自動化卡件
調試：打開驅動器的控制電壓后，僅顯示兩個點最初會亮起。
初始化成功后，如果沒有錯誤或警告掛起，則顯示為bb。
如果AS繼電器已連接，且電源裝置的電源電壓則驅動控制器讀取Ab。
控制應用啟用后，驅動控制器讀取AF。
警告：只要應用警告，驅動器就會在H1中顯示診斷顯示，但沒有其他響應。
例外：如果應用了電源部分的警告超溫超過30秒，并且在試驗過程中沒有來自控制裝置的反應
此時，電源部分的錯誤信息為并開始斷電。
錯誤：如果發生錯誤，則將其存儲并顯示在H1顯示中。
錯誤和狀態顯示由/SH2的負側翼清除來自控制。只有在控制關閉且然后再次。
如果警告和錯誤同時掛起，則錯誤具有優先級并顯示。
如果同時發生多個錯誤，則只有第一個錯誤顯示。
供應和附加組件：可以讀取電源和其他部件的詳細診斷在相關單位關閉。
帶供應裝置的驅動器上既沒有讀數也沒有反應警告，例如散熱器超溫預警。
如果HVR供電裝置發出反饋過載警告驅動控制器的電源端級被短時間鎖定。這個驅動器不顯示此信息，也不向控制器發送信號。
驅動控制器的驅動啟用在電源單元中被移除發出錯誤信號。還生成連接控件的消息。
連接錯誤：如果控制器將兩個PWM連接器連接到一個驅動軸，則產生錯誤并顯示診斷88。
Commissioning:
After switching on the control voltage of the drive, only the two display
points will initially light up.
After the initialization has been successful, and if no error or warning are
pending, then the display reads bb.
If the AS relay is connected and the power voltage at the supply unit has
been brought into load, then the drive controllers read Ab.
After the control has applied the enable, then the drive controller reads
AF.
Warnings:
As long as a warning is applied, the drive displays the diagnoses in the H1
display, but no other response ensues.
Exception: If the warning overtemperature in power section is applied
longer than 30 seconds and there is no reaction from the control during
this time, then the error message overtemperature in power section is
generated and a power shutdown is started.
Error:
If an error occurs, then it is stored and shown in the H1 display.
The error and status display are cleared by a negative flanke from /SH2
from the control. This is only possible if the control is switched off and
then on again.
If a warning and an error are both pending simultaneously, then the error
has priority and is displayed.
If more than one error occurs at the same time, then only the first is
displayed.
Supply and additional components:
Detailed diagnoses of the supply and additional components can be read
off at the relevant units.
There is neither a reading nor a reaction at the drive with supply unit
warnings, e.g., heatsink overtemperature prewarning.
In the case of a feedback overload warning from HVR supply units, the
power end stages of the drive controller are locked for a short time. The
drive does not display this nor does it signal this to the control.
The drive enable of the drive controller is removed is the supply unit
signals an error. A message for the connected control is also generated.
Connectionerror:
If the control connects two PWM connectors to one drive axis, then an
error is generated and diagnosis 88 displayed.
