產品內容介紹
SCHENCK A909001.02控制器
連接方式當輸出電壓超過額定值時，請確保最大輸出功率低于額定值。此外，當輸出電壓低于額定值時，請確保最大輸出電流低于額定值。使用時請考慮以下特性。*可調輸出電壓在輸出的20%（3V型號：30%）內（小于PV電壓的1V）與PV電壓成正比，并具有線性特性。然而，對于輸出電壓在輸出電壓的10%以內（約小于光伏電壓的0.5V），輸出將進入間歇模式，紋波電壓變大，電源也會發出不規則的聲音。然而，這不是損害。也會有欠壓閉鎖保護功能觸發電源關閉的情況。輸出關閉時，低輸出檢測功能（PF）觸發PF信號并將其設置為“H”，同時輸出LED關閉。在電壓鎖定保護模式下，關閉輸入幾分鐘，然后再次打開輸入進行恢復。通過將遠程ON/OFF控制信號轉到OFF和ON，也可以從欠壓鎖定中恢復。欠壓檢測值使用自動跟蹤模式，該模式跟隨輸出電壓，并在保護功能模式下始終對應輸出電壓的70%-80%。基于上述解釋，我們將不在產品保修范圍內使用輸出電壓20%以內的可調輸出電壓。對于要求輸出電壓在20%以內變化的應用，請在操作前考慮以上內容。對于要求輸出電壓低于20%的應用，由于用戶系統的應用類型不同，可能存在與上述不同的情況（行為）。因此，請與用戶系統核實。
輸出峰值電流
對于輸出峰值電流的型號，請滿足以下條件。根據第6-1節中的輸出降額降低峰值電流值。當額定電流和連續峰值輸出時間（τ）在使用過程中超過額定值時，保護電路會關閉輸出。當保護電路激活時，輸入被暫時切斷幾分鐘，然后重新輸入電源或輸入遠程ON/off控制信號以恢復輸出。輸入電壓范圍：AC180V-265V連續峰值輸出時間（τ）：10秒內峰值輸出電流（Ip）：額定峰值輸出電流內安裝方向如下。標準安裝方法為（A）。方法（B）、（C）和（D）也是可行的。禁止使用（A）、（B）、（C）和（D）以外的安裝方法（例如：（E）和（F））。
安裝方法注意事項（1）此電源設備是一個帶有內置風扇的強制空氣冷卻系統。（2） 該電源在前面板和后面板上有通風孔。保持這些區域與前側的距離大于100mm，與后側的距離大于50mm。（3） 請注意，在多塵環境中，通風會惡化。（4） 內置風扇是壽命有限的部件，需要定期更換。（更換將收費）。（5） 該電源的環境溫度與正面中心的距離小于50mm。（6） 安裝螺釘?shù)淖畲笤试S穿透深度為6mm。安裝螺釘?shù)穆菁y不完整不得穿透。（7） 安裝螺釘（M4）的建議扭矩為1.27 N?m。
Connection method
When output voltage is over rated value, please make sure that maximum output power is below rated value. Moreover, when output voltage is below rated value, please make sure that maximum output current is below rated value. Please consider the following characteristic during usage.* Adjustable output voltage within 20%(3Vmodel : 30%) of output (less than 1V of PV voltage) is proportional to PV voltage and has a linear characteristic. However, for output voltage within 10% of output (about less than 0.5V of PV voltage), output will go into intermittent mode and ripple voltage becomes large, also irregular sound is release from the power supply. However, it is not damage. There will also be cases of the power supply shutting down triggered by under voltage lock out protection function. With output shutting down, low output detection function (PF) triggers the PF signal and set it to "H", and also output LED is switch off. Under voltage lock out protection mode, switch off input for a few minutes and then switch on input again for recovery. Recovery from under voltage lock out is also possible by turning remote ON/OFF control signal OFF and ON. Under voltage detection value uses an automatic tracking mode, which follows the output voltage and constantly correspond to the 70%-80% of output voltage with a protection function mode. Base on the explanation above, we will kindly exclude the usage of adjustable output voltage within 20% of the output voltage from the product warranty. For application that requires variable output voltage within 20% of output voltage, please kindly consider the above contents prior to operation. For application that requires output voltage below 20%, due to different type of application for the user's system, there might be a situation (behavior) different from the one mentioned above. Therefore please check with the user system.
Output peak Current
For model with output peak current, please meet the following condition. Reduce peak current value according to output derating as section 6-1. The output is shut down by protection circuit when rated current and continuous peak output time (τ) exceeds rated value during usage. When protection circuit is activated, input is temporarily cut off for a few minutes and then power is re-input or remote ON/OFF control signal should be input for recovery of the output. Input voltage range ：AC180V - 265V Continuous Peak output time(τ) ：Within 10 seconds Peak output current(Ip) ：Within the rated peak output current Mounting directions are as follows. Standard mounting method is (A). Methods (B), (C) and (D) are also possible. Mounting methods besides (A),(B),(C) and (D) (example : (E) and (F)) are inhibit.
Mounting Method Caution (1) This Power supply unit is a forced air-cooling system with a built-in fan. (2) This power supply has ventilating holes on the front and back panels. Keep these areas freely more than 100mm from front side and more than 50mm from rear side. (3) Please note that ventilation will be worsened in a dusty environment. (4) Built-in fan is limited life part, which require periodic replacement. (Replacement will be charge). (5) The ambient temperature of this power supply is less than 50mm from the center of a front side. (6) The maximum allowable penetration of mounting screw is 6mm. Incomplete thread of mounting screw should not be penetrated. (7) Recommended torque for mounting screw (M4) is 1.27 N?m.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
