產品詳情介紹
Honeywell 51401583-100 EPNI輸出接口模塊
監測溫度傳感器持續監測模塊的工作溫度。處理器模塊的溫度狀態指示是否已超過以下環境溫度范圍的溫度閾值
中斷工作電壓后，控制器可能不會自動重新啟動。如果一個處理器模塊的模式開關處于停止位置，并且在重新連接工作電壓時，此處理器模塊意外地第一個啟動，則它仍處于停止?fàn)顟B(tài)。因此，其他處理器模塊也無法啟動。如果在中斷工作電壓后需要自動啟動，則所有處理器模塊上的模式開關必須設置為運行！開關位置：運行至安全相關操作設置！影響：非冗余操作：如果自動啟動被激活，處理器模塊將啟動用戶程序。冗余操作：處理器模塊采用與其他處理器模塊相同的操作狀態。如果溫度超過特定閾值或低于該閾值，溫度狀態將發生變化。表14適用于帶運行風扇的正常運行。如果出現異常操作，例如，沒有風扇，溫度狀態可能表明即使在較低的環境溫度下也已超過溫度閾值。溫度狀態是處理器模塊的狀態。登錄處理器模塊后，模塊狀態顯示在SILworX控制面板中。
操作系統
加載到CPU中的操作系統包含HIMax可編程電子系統（PES）的所有基本功能，例如：處理用戶程序，執行硬件和軟件的所有測試?yán)谐绦蛑芷跁r(shí)間監控（看門狗）與I/O模塊的安全通信與其他系統的安全通信，例如：-HIMax-HIMatrix創建和存儲事件。有關操作系統功能的說明，請參閱系統手冊（HI 801 001 E）。周期處理CPU周期通過以下階段運行：讀取輸入數據處理用戶程序?qū)懭胼敵鰯?shù)據其他活動，例如重新加載處理連接器板X(qián)-CB 001 01連接器板將模塊與其他HIMA控制器或PADT連接。模塊和連接器板一起構成一個功能單元。連接器板包含處理器模塊上以太網交換機的四個端口（Eth1…Eth4）。要啟動處理器模塊，請將處理器模塊插入允許的基板插槽中，參見第4.1.1章。如果基板已經在運行，處理器模塊將啟動并采用通過其配置和模式開關位置設置的運行狀態。如果基板不工作，請連接電源電壓。
Monitoring the Temperature
Sensors continuously monitor the operating temperature of the modules. The temperature status of a processor module indicates wether the temperature thresholds have been exceeded with respect to the following environment temperature ranges
The controller might not restart automatically after interrupting the operating voltage If the mode switch of one processor module is in the Stop position and this processor module is accidentally the first to be started when the operating voltage is reconnected, it remains in the STOP state. Consequentially, also the remaining processor modules cannot start. If an Autostart is required after interrupting the operating voltage, the mode switches on all the processor modules must be set to Run! Switch Position: Run To set for safety-related operation! Effect: ? Non-redundant operation: The processor module starts the user programs if Autostart is activated. ? Redundant operation: The processor module adopts the same operating state as the other processor modules.If the temperature exceeds a specific threshold or falls below it, the temperature status changes. Table 14 applies to normal operation with operating fans. In case of abnormal operation, e.g., without fans, the temperature status can indicate that the temperature thresholds have been exceeded even at a lower environment temperature. The temperature status is a status of the processor module. After logging in to the processor module, the module status is displayed in the SILworX Control Panel.
Operating System
The operating system loaded into the CPU contains all basic functions of the HIMax programmable electronic system (PES), for example: ? Processing the user programs, ? Performing all test routines for hardware and software ? Cycle time monitoring (watchdog) ? Safe communication with the I/O modules ? Safe communication with other systems, such as: - HIMax - HIMatrix ? Creating and storing events. For a description of the operating system functions, see the System Manual (HI 801 001 E). Cycle Processing A CPU cycle runs through the following phases: ? Reading the input data ? Processing the user programs ? Writing the output data ? Other activities, e.g., reload processing Connector Board The X-CB 001 01 connector board connects the module with other HIMA controllers or with the PADT. Module and connector board form together a functional unit. The connector board contains the four ports (Eth1...Eth4) of the Ethernet switch on the processor module.To start up the processor module, insert the processor module into a permissible base plate slot, see Chapter 4.1.1. If the base plate is already operating, the processor module starts and adopts the operating state set through its configuration and the mode switch position. If the base plate is not operating, connect the supply voltage.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
