MVME712/AM機械備件
?如果要在下載時使用DriveWindow，而上的節點地址未被使用，則無需更改硬件。16.1.2下載系統軟件如果您在下載新系統軟件時未使用DriveWindow，請退出DriveWindow。如果您在下載中使用DriveWindow（您有一個DriveWindow加載包），則應在下載系統軟件之前停止所有聯機活動（狀態刷新、監視、無項目聯機、控制未執行）。16.1.3恢復參數下載系統軟件后，驅動器通常位于節點地址1，所有參數均設置為默認值。如果在下載系統軟件時使用了DriveWindow以外的其他工具，請啟動DriveWindow。如果驅動器包含應用程序宏，請驗證所選宏在保存的參數文件和驅動器中是否相同。如果需要，在驅動器中更換。下載保存的參數。是否還下載ID運行結果參數取決于系統軟件版本的兼容性級別。如果驅動器最初位于一個以外的其他節點地址，則通常在重新啟動后會位于其原始地址。如果DriveWindow請求重新啟動時未完成，則需要重新標識網絡。通過斷開并重新連接OPC服務器來完成重新識別。參數、信號和故障4-138 DriveWindow 2如果節點地址發生變化，當DriveWindow重新啟動驅動器時，您可能會收到一條錯誤消息，告訴您重新啟動失敗。如果單擊“確定”按鈕后，驅動器重新出現在瀏覽樹窗格中的新節點地址，則可以忽略該消息。這是因為DriveWindow在重新連接OPC服務器之前不知道節點地址的更改。因此，它試圖驗證從錯誤的節點地址重新啟動的成功。16.1.4整理我們建議您對所有已升級的驅動器進行完全備份，以便用備件更換損壞的控制板。請注意，您可以選擇使用舊備份包，而不是創建新的備份包，只替換其中升級的驅動器。另請參閱：什么是參數和信號如何保存參數如何恢復參數如何比較參數什么是參數文件什么是系統軟件什么是備份包什么是加載包如何備份如何下載17.桌面首選項使用桌面首選項，您可以控制DriveWindow顯示的某些行為。請注意，大多數設置只是項目集屬性的默認設置。因此，它們可以通過不使用默認選擇而被項集覆蓋。然而，通過在項目集中使用默認值（如果合適），您可以快速更改所有此類項目集的某些行為。否則，您需要分別更改所有此類項集的屬性。參數、信號和故障驅動窗口2 4-139您可以通過選擇桌面菜單中的首選項命令來設置桌面首選項。上下文菜單中包含相同的命令，您可以通過在項目名稱外的項目集窗格上單擊鼠標右鍵來獲得該命令。
? If you are going to use DriveWindow in downloading, and node address on is not in use, no hardware changes are needed. 16.1.2 Downloading System Software If you are not using DriveWindow in downloading the new system software, quit DriveWindow. If you use DriveWindow in downloading (you have a DriveWindow loading package), you should stop all on-line activity (status refresh, monitoring, no items on-line, control not taken) before downloading system software. 16.1.3 Restoring Parameters When system software has been downloaded, the drive is normally found at node address one with all parameters set to default values. If you used other tool than DriveWindow in downloading system software, start DriveWindow. If drive contains application macros, verify that the selected macro is the same in the saved parameter file and in the drive. Change it in the drive, if needed. Download the saved parameters. Whether to download also the ID run result parameters or not, depends on the level of compatibility of the system software versions. If the drive originally was at some other node address than one, it will usually be at its original address just after restarting it. If restarting is not done when DriveWindow is requesting it, is required to reidentify the network. Re-identifying is done by disconnecting and re-connecting the OPC Server. Parameters, Signals, and Faults 4-138 DriveWindow 2 If the node address changes, when DriveWindow restarts the drive, you will probably get an error message, which tells you that restarting failed. If, after you click the OK button, the drive re-appears in the browse tree pane at the new node address, you may ignore the message. It is shown, because DriveWindow does not know about the node address change before re-connecting the OPC Server. Thus it tries to verify success of restarting from the wrong node address. 16.1.4 Finishing We recommend that you take full backup of all drives, which were upgraded, so that replacing a damaged control board with a spare part is made easy. Note that instead of creating a new backup package, you have the option to use the old backup package, and only replace the upgraded drives within it. See Also: What are Parameters and Signals How to Save Parameters How to Restore Parameters How to Compare Parameters What is Parameter File What is System Software What is a Backup Package What is a Loading Package How to Backup How to Download 17. Desktop Preferences With desktop preferences you can control some behaviour of DriveWindow display. Note that most of the settings are just defaults for item set properties. They can thus be overridden by an item set by not using the default selection there. However, by using defaults in item sets, where appropriate, you can quickly change some behaviour of all such item sets. Otherwise you would need to change the property for all such item sets separately. Parameters, Signals, and Faults DriveWindow 2 4-139 You can set desktop preferences by selecting Preferences command in the Desktop menu. The same command is included in the context menu, which you get by clicking with the right mouse button on the item sets pane outside the name of an item.
