MVME172P-644SE工控模塊卡件
440F-C4000D圖4替代肋條圖案。如圖所示，墊傳感器具有兩種不同的肋圖案。任一圖案均可用作上表面。方格圖案在各個方向都能提供最佳抓地力。直肋圖案更易于軟管/沖洗，更適合在骯臟或衛生敏感的應用中使用。網紋羅紋圖案直羅紋圖案A1 A2110/230VAC可選復位IND 1 2 MC Y1 Y3 Y5 13 23 31復位IND 3 4 MC Y2 Y4 Y6 14 24 32 24V AC/DC+-Y1 Y2 Y3 Y 4 Y5 Y6+-K1 AUX K1 AUX K2 L1L2 L3遠程復位按鈕（如果需要）照明（如果需要的話）110/230V AC電源L N 24V AC/DC電源可選遠程指示裝置接觸器控制電源輔助傳感器矩陣監控7第3節-應用重要的是，保護系統的類型適合其預期應用。對機械或過程進行風險評估的文件化過程將揭示危險的身份和性質以及其他相關信息。然后，應將防護系統的特性與風險評估結果進行比較，以確定是否可以將風險降低到可接受的水平。
在某些應用中，為了達到可接受的風險水平，可能需要組合使用多種類型的防護系統。該系統旨在通過感應人員在機器周圍的地板區域和其他類似危險來保護人員。該系統只能在給定的規格范圍內使用，并嚴格按照本手冊中提供的信息進行安裝。該系統本身不能防止材料、氣體和輻射噴射造成的危險。對于這些應用，可能需要額外的保護措施，如物理防護。該系統不打算用作外圍防護。該系統不打算用作機器啟動或重新啟動裝置。機器控制電路的配置必須確保系統輸出觸點的閉合能夠啟動機器的啟動電路，但不會直接導致機器啟動。機器的啟動或重新啟動只能通過在指定的機器控制裝置上進行單獨的故意操作來實現。該系統不適用于爆炸性環境。如果需要有關系統適用于特定應用的進一步指導，請聯系供應商。用作組合跳閘和存在傳感系統圖5用作組合跳閘與存在傳感系統。
440F-C4000D Figure 4 replaces the rib pattern. As shown in the figure, the cushion sensor has two different rib patterns. Any pattern can be used as the upper surface. The checkered pattern provides optimal traction in all directions. Straight rib pattern is easier to hose/rinse and is more suitable for dirty or sanitary sensitive applications. Rib Pattern Straight Rib Pattern A1 A2110/230VAC Optional Reset IND 1 2 MC Y1 Y3 Y5 13 23 31 Reset IND 3 4 MC Y2 Y4 Y6 14 24 32 24V AC/DC+- Y1 Y2 Y3 Y 4 Y5 Y6+- K1 AUX K1 AUX K2 L1L2 L3 Remote Reset Button (if required) Lighting (if required) 110/230V AC Power Supply L N 24V AC/DC Power Supply Optional Remote Indicator Contactor Control Power Supply Auxiliary Sensor Matrix Monitoring 7 Section 3 - Application Important, The type of protection system is suitable for its intended application. The documented process of risk assessment of a machine or process will reveal the identity and nature of the hazard and other relevant information. The characteristics of the protection system shall then be compared with the results of the risk assessment to determine whether the risk can be reduced to an acceptable level.
In some applications, it may be necessary to combine multiple types of protection systems in order to achieve an acceptable level of risk. The system is designed to protect people by sensing people in the floor area around the machine and other similar hazards. The system can only be used within the given specification range, and shall be installed in strict accordance with the information provided in this manual. The system itself does not protect against the hazards caused by material, gas and radioactive jets. For these applications, additional protective measures, such as physical protection, may be required. The system is not intended for perimeter protection. The system is not intended to be used as a machine starting or restarting device. The configuration of the machine control circuit must ensure that the closing of the system output contacts can start the starting circuit of the machine, but will not directly cause the machine to start. The starting or restarting of the machine can only be achieved through separate intentional operation on the designated machine control device. The system is not suitable for explosive environments. If you need further guidance on the suitability of the system for a particular application, please contact the supplier. Used as a combined trip and presence sensing system Figure 5 is used as a combined trip and presence sensing system.
