MVME172P-642LSE自動化模塊備件
必須記錄危險區域的尺寸和位置以及使用的假設，以便檢查防護措施的充分性。如果其他防護措施與墊子系統一起使用，可能會影響確保蓋子和格柵與地板表面齊平。無松散碎屑或突起。傳感器墊不得下垂或起伏。沒有鋒利的邊緣。傳感器墊傳感器墊16對墊的尺寸和位置的要求，如圖11所示。圖11。注意：固定防護裝置應符合EN 953、EN 294和EN 811的要求。首先，確定需要穿過墊系統無障礙進入危險區域的路線?？紤]所有日常訪問需求，如產品檢查、機器檢查和調整、刀具更換和清除堵塞。還應考慮過程的視覺觀察。在干預過程中，考慮機器附近人員和輔助設備的空間要求。安全距離計算對于使用墊子系統作為組合跳閘和存在感測系統的應用，應根據EN999進行計算。圖12的流程圖顯示了基本步驟。注：如果機器的設計符合該機器的現有協調歐洲“C”型標準，該標準給出了具體公式或最小距離，則應優先使用EN 999中給出的公式。傳感器墊危險危險傳感器墊傳感器墊固定防護延伸固定防護箭頭顯示通道17圖12流程圖顯示方法計算的最小距離是傳感器墊檢測區外緣到危險最近部分的最小水平距離。地面安裝式安全墊的EN 999公式為S=（1600 x T）+1200mm S是最小安全距離，單位為毫米。系數1600是基于進場速度1600mm/S的標準假設。T是以秒為單位的總停止時間。增加的1200mm是EN 999中給出的參數C，并考慮了步幅長度和手臂伸展。
是C類標準中是否給出了具體公式或最小距離？根據C類標準確定最小距離使用此最小距離根據prEN 999中的公式計算最小距離是否可以達到此最小距離？最小距離是否允許人員在危險區域內而不被發現？使用此最小距離以及根據風險采取的補充措施使用該最小距離是否可以縮短總體響應時間，或者是否可以縮短參數C？減少總響應時間和/或減少參數C使用附加或替代保護設備18總停止時間T由兩部分組成：T=t1+t2 t1是啟動傳感功能和輸出信號開關設備處于關閉狀態之間的最長時間。對于墊子系統，t1=35mS。t2是機器的響應時間，即在接收到來自墊系統的輸出之后停止機器或消除風險所需的時間。計算中使用的機器的響應時間需要是最壞情況下的時間。有些機器的響應時間不一致，這取決于操作模式、工件的性質以及啟動停止的操作周期點。如果制動器等的磨損會影響響應時間，則應考慮磨損。在某些情況下，可能需要考慮機器控制系統的進一步延遲。計算示例在本示例中，墊子系統與最壞情況下響應時間測量為0.485秒的機器一起使用。使用公式，T=t1+t2=35mS+485mS=520mS=0.520S S=（1600 x 0.520）+1200mm=832+1200mm=2032mm從2032mm到機器底板邊緣，需要傳感器墊。5.4.2用作周界防護區域內的存在感測系統如果危險周圍區域完全封閉在防護周界內，prEN 999的要求可能不適用。在這些應用中，墊子系統檢測操作員的存在，以防止操作員在外殼內時重置周界防護系統并重新啟動機器。
The size and location of the hazardous area and the assumptions used must be documented in order to check the adequacy of the protective measures. If other protective measures are used together with the mat subsystem, it may affect ensuring that the cover and grille are flush with the floor surface. No loose debris or protrusions. The sensor pad must not sag or fluctuate. No sharp edges. The requirements of sensor pad 16 on the size and position of the pad are shown in Figure 11. Figure 11. Note: The fixed protective device shall comply with the requirements of EN 953, EN 294 and EN 811. First, determine the route that needs to pass through the mat system to enter the hazardous area unobstructed. Consider all daily access needs, such as product inspection, machine inspection and adjustment, tool replacement, and removal of blockages. Visual observation of the process should also be considered. During the intervention, consider the space requirements for personnel and auxiliary equipment near the machine. Safety distance calculation For applications using the mat subsystem as a combined trip and presence sensing system, it shall be calculated according to EN999. The flowchart in Figure 12 shows the basic steps. Note: If the design of the machine complies with the existing harmonized European "C" standard for the machine, which gives a specific formula or a minimum distance, the formula given in EN 999 shall prevail. Sensor pad Hazard sensor pad Sensor pad Fixed protection Extended fixed protection arrow Display channel 17 Figure 12 Flow chart Display method The minimum distance calculated by the display method is the minimum horizontal distance from the outer edge of the sensor pad detection area to the nearest part of the hazard. The EN 999 formula of ground mounted safety pad is S=(1600 x T)+1200mm S is the minimum safety distance, and the unit is mm. The coefficient 1600 is a standard assumption based on the approach speed of 1600mm/S. T is the total stop time in seconds. The increased 1200mm is the parameter C given in EN 999, taking into account stride length and arm extension.
Is there a specific formula or minimum distance in the Class C standard? Determine the minimum distance according to the Class C standard Use this minimum distance to calculate the minimum distance according to the formula in prEN 999 Can you reach this minimum distance? Does the minimum distance allow people to stay in the hazardous area without being found? Can the use of this minimum distance and supplementary measures taken according to the risk reduce the overall response time, or can the parameter C be shortened? Reducing the total response time and/or reducing the parameter C using additional or alternative protective devices 18 The total stop time T consists of two parts: T=t1+t2 t1 is the longest time between starting the sensing function and closing the output signal switchgear. For mat subsystem, t1=35mS. T2 is the response time of the machine, that is, the time required to stop the machine or eliminate the risk after receiving the output from the cushion system. The response time of the machine used in the calculation needs to be the worst case time. Some machines have different response times, depending on the mode of operation, the nature of the piece, and the point at which the operation cycle starts and stops. If the wear of brakes, etc., affects the response time, wear should be considered. In some cases, further delays in the machine control system may need to be considered. Calculation Example In this example, the mat system is used with a machine that has a worst case response time measurement of 0.485 seconds. Using the formula, T=t1+t2=35mS+485mS=520mS=0.520S S=(1600 x 0.520)+1200mm=832+1200mm=2032mm from 2032mm to the edge of the machine floor, sensor pads are required. 5.4.2 The requirements of prEN 999 may not be applicable if the hazardous surrounding area is completely enclosed within the protective perimeter. In these applications, the mat subsystem detects the presence of the operator to prevent the operator from resetting the perimeter protection system and restarting the machine while inside the enclosure.
