MVME162PA-242LNS自動化卡件
日常維護檢查和測試建議每周或維修后停止機器，清潔型材并干燥。檢查型材表面是否損壞。任何刺穿型材的損壞都可能讓材料或液體進入。必須立即處理。檢查所有端蓋角和接頭是否牢固且無損壞。必須立即更換損壞的零件。測試配置文件操作。兩個人可能需要一個人按下配置文件，一個人觀察控制單元的操作。在使用手動復位模式的系統上，必須連續按下復位按鈕。檢查配置文件未按下時“綠色”是否亮起，“紅色”是否點亮。啟動機器，按下配置文件并檢查機器是否立即停止。如果這些檢查發現任何問題，則在糾正之前不得使用機器。將所有檢查和測試記錄在書面日志中。徹底檢查和測試每年兩次或維修后由電氣和機械工程方面的合格人員進行。 執行 中的測試，隔離機器和系統的電源。遵守電氣安全預防措施。 徹底檢查型材和部件有無機械損壞。 斷開端子處的輪廓線。將輪廓線的導線連接到歐姆表的輸入端?，F(xiàn)在，一個人應該用一只手按壓條帶上的每個點。電阻測量值應為? + 未按下型材時為，按下型材時不超過。如果檢查發現任何問題，則在糾正之前不得使用機器。將檢查和測試記錄在書面日志中。 維護和服務故障查找指南癥狀可能原因檢查剖面中的“黃色”開路或端子是否牢固。照明。連接接線。電纜斷裂剖面圖損壞。即使電源故障，也不會點亮。電壓選擇開關設置正確。輪廓被按下。電源保險絲。存在電源電壓。除非復位失敗，否則不會點亮。如果使用接觸器監視器，請檢查是否按下配置文件，然后每個接觸器是否正常工作
Daily maintenance, inspection and testing suggest stopping the machine every week or after maintenance, cleaning and drying the profiles. Check whether the profile surface is damaged. Any damage that pierces the profile may allow material or liquid to enter. It must be handled immediately. Check that all end cap corners and connections are secure and undamaged. Damaged parts must be replaced immediately. Test configuration file operation. Two people may need one to press the configuration file and the other to observe the operation of the control unit. On systems using manual reset mode, the reset button must be pressed continuously. Check whether "green" lights up and "red" lights up when the configuration file is not pressed. Start the machine, press the configuration file and check if the machine stops immediately. If these checks reveal any problems, do not use the machine until it is corrected. Record all inspections and tests in a written log. Thorough inspection and testing shall be conducted twice a year or by qualified personnel in electrical and mechanical engineering after maintenance. Perform the test in to isolate the power supply of the machine and system. Observe electrical safety precautions. Thoroughly inspect the profiles and components for mechanical damage. Disconnect the contour line at the terminal. Connect the lead of the contour line to the input of the ohmmeter. Now, one should press each point on the strip with one hand. The measured resistance value shall be ?+when the profile is not pressed, it shall not exceed. If any problems are found during the inspection, the machine must not be used until it is corrected. Record inspections and tests in a written log. Maintenance and Service Fault Finding Guide Possible Causes of Symptoms Check the "yellow" open circuit in the section or whether the terminal is secure. Lighting. Connect the wiring. The cable fracture profile is damaged. It will not light up even if the power supply fails. The voltage selector switch is set correctly. The contour is pressed. Power fuse. Supply voltage is present. It will not light up unless reset fails. If a contactor monitor is used, check whether the configuration file is pressed, and then whether each contactor works normally
