MVME162-521A PLC工控備件
注意連接器設計為在電機安裝期間旋轉到固定位置，并保持在該位置，無需進一步調整。不要多次旋轉連接器，也不要使用工具或過度用力旋轉連接器。過度旋轉或用力會損壞連接器密封，降低電機的國際防護等級，如第頁規范所述。注意僅對電機連接器和電纜插頭施加力。不要對從電纜插頭伸出的電纜施加力。不要使用工具例如鉗子和虎鉗旋轉連接器。系列或更小框架尺寸的低慣量無刷伺服電機年月安裝電機按照以下步驟安裝電機。為電機提供足夠的間隙散熱片和氣流，使其保持在的工作溫度范圍內。除非強制冷卻空氣穿過電機，否則不要封閉電機，并使其他發熱設備遠離電機。散熱器要求在第頁規范的腳注中列出。驗證應用的軸向和徑向軸負載不超過第頁電機負載力額定值中列出的值。將電機與電纜連接放置在電機下方。有關正確電機和電纜定位的視覺參考，請參閱第頁的拆卸軸蓋。正確安裝和對齊電機電機包括一個安裝導向器，用于在機器上對齊電機。當軸鍵與連接器對齊時，線編碼器上出現索引脈沖。確保皮帶負載在電機限制范圍內，并且所有皮帶和滑輪正確對齊。遵循齒輪箱滑輪或其他電機附件的制造商建議。注意如果在安裝聯軸器和皮帶輪期間對軸施加劇烈沖擊，可能會損壞電機軸承和反饋裝置。在安裝或拆卸過程中，不要用工具敲擊聯軸器或皮帶輪。注意電機的外表面在運行過程中可能會達到的高溫。采取預防措施，防止意外接觸熱表面。選擇電機配合連接和電纜時，應考慮電機表面溫度。系列或更小框架尺寸的低慣量無刷伺服電機年月連接電機電纜安裝電機后，按照以下步驟連接反饋和動力制動電纜。
Note that the connector is designed to rotate to a fixed position during motor installation and remain in that position without further adjustment. Do not rotate the connector more than once, nor use tools or excessive force to rotate the connector. Excessive rotation or force can damage the connector seal and reduce the international protection level of the motor, as described in the specifications on page. Note that only force is applied to the motor connector and cable plug. Do not apply force to the cable protruding from the cable plug. Do not use tools such as pliers and vises to rotate the connector. Low inertia brushless servo motor with frame size of series or smaller shall be installed according to the following steps. Provide the motor with enough clearance, radiator and air flow to keep it within the operating temperature range of. Do not close the motor and keep other heating equipment away from the motor unless forced cooling air passes through the motor. The radiator requirements are listed in the footnote to the specification on page. Verify that the applied axial and radial shaft loads do not exceed the values listed in Motor Load Force Ratings on page. Place the motor and cable connection under the motor. For a visual reference to correct motor and cable positioning, refer to Removing the Shaft Cover on page. Proper mounting and alignment of the motor The motor includes a mounting guide for aligning the motor on the machine. When the axis key is aligned with the connector, the index pulse appears on the wire encoder. Make sure that the belt load is within the limits of the motor and that all belts and pulleys are correctly aligned. Follow the manufacturer's recommendations for gearbox pulleys or other motor accessories. Note that if severe impact is applied to the shaft during the installation of the coupling and pulley, the motor bearing and feedback device may be damaged. Do not knock the coupling or pulley with tools during installation or removal. Pay attention to the high temperature that the outer surface of the motor may reach during operation. Take precautions to prevent accidental contact with hot surfaces. The motor surface temperature shall be considered when selecting the motor mating connection and cable. Low inertia brushless servo motor of series or smaller frame size shall be connected with motor cable. After installing the motor, connect the feedback and power brake cables according to the following steps.
