NI PXIe-5652射頻信號發生器
1.產 品 介 紹
品牌：NI
型號：NI PXIe-5652
產品說明：射頻信號發生器
優勢：供應進口原裝正品，專業停產配件。
2.產 品 詳 情 資 料：
NI PXIe-5652這些跳線位置（標記為JP2、JP3和JP4）可通過移除轉換器頂部的方形塑料蓋來訪問。NI PXIe-5652可以根據需要更改配置，方法是使用一對尖嘴鉗小心地移除一個或多個跳線，并將其放置在所需的一對引腳上。請參閱下表中這些可選跳線位置的說明，并將跳線放置在所選引腳對上。NI PXIe-5652管腳編號為1、2和3。默認跳線位置由每個位置的跳線引腳周圍的矩形表示。默認管腳編號為1和2。當與PLC通信的設備不提供載波檢測信號時，使用默認位置1和2。JP2強制RS-485端口上的DCD信號激活。如果設備確實提供載波檢測信號，請使用跳線位置2和3。這允許編程設備控制DCD。當連接的調制解調器不需要清除發送（CTS）信號時，使用默認位置1和2。這允許編程設備控制RTS信號。NI PXIe-5652
These jumper positions, labeled JP2, JP3, and JP4, are accessed by removing the square plastic cover on the top of the converter. Configuration NI PXIe-5652can be changed as required by carefully removing one or more of the jumpers with a pair of needle nose pliers and placing it on the desired pair of pins. Refer to the description of these selectable jumper positions in the following table and place the jumper on the selected pair of pins. The pin numbers are 1, 2, and 3. Default jumper locations are indicated by a rectangle around the pins to be jumpered for each position. NI PXIe-5652The default pin numbers are 1 and 2.Default position 1 and 2 is used when the device communicating with the PLC does not supply the Carrier Detect signal. JP2 forces the DCD signal active on the RS-485 port.NI PXIe-5652Use jumper positions 2 and 3 if the device does supply the Carrier Detect signal. This allows the programming device to control DCD.Default position 1 and 2 is used when an attached Modem does not require the Clear To Send (CTS) signal. This allows the programming device to control the RTS signal.
3.產 品 展 示
4.公 司 優 勢
5.關 于 我 們
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://m.wzljsf.com
