GE PIB 102A MV7306P23阿爾斯通控制板的應用
熱備CPU冗余功能
有關熱備用CPU冗余系統的配置和操作的詳細信息，請參閱PACSystems熱備用CPU冗余用戶手冊，GFK-2308。
? 通過以太網網絡接口單元（ENIU）支持單個和冗余以太網遠程I/O局域網模塊
? 支持單工和冗余控制的PROFINET遠程IO（需要固件版本8.00或更高版本）
? 在任何一個單點故障中幸存
? 無碰撞開關
o同步CPU
o單掃描切換
o傳輸數據大小可達2M字節；在CPU硬件配置和變量屬性中選擇
? 支持兩條冗余通信鏈路 故障部件的在線修復
? 在線編程
? 冗余存儲器交換模塊
o用于角色切換的手動撥動開關，用于將控制從活動單元轉換到備用單元
o冗余狀態指示燈
? 應用程序啟動的角色切換，將活動單元切換到備份狀態
? 冗余狀態位和消息記錄
? 內存錯誤檢查和糾正（ECC）、單位糾正和多位檢查
? 背景診斷
HSB控制策略
HSB控制策略具有以下特點：
? 在重新同步時，活動單元不會自動切換到主單元
? 輸出數據傳輸中必須包括關鍵控制數據和所有冗余輸出
? 從活動單元到備用單元的無碰撞切換本產品用于RX3i系統。其部件被視為開放式設備（帶電用戶可接近的電氣部件），并且必須安裝在最終外殼中，即：制造以提供安全。外殼至少應提供一定程度的固體防護小到12mm的物體（例如手指）。這相當于NEMA/UL 1型外殼或IEC60529 IP20提供至少2級污染環境的等級。有關安裝RX3i機架系統的詳細信息，請參閱PACSystems RX3i系統手冊，GFK-2314。
危險區域的安裝以下信息適用于帶有危險區域UL標志或ATEX標志的產品：
爆炸性環境：1類2組ABCD
? 該設備為開放式設備，安裝在適用于只有使用工具才能訪問的環境。
? 適用于I類2類A、B、C和D組危險場所或非危險場所
? 警告-爆炸危險-替換部件可能會損害I類的適用性，第2部分。
? 警告-當處于危險位置時，在更換或接線前關閉電源模塊。
? 警告-爆炸危險-只能在已知無危險的區域更換電池。
ATEX 2區該模塊必須安裝在符合EN60079-15認證的外殼中，用于IIC組2區防護等級為IP54。外殼只能使用工具打開。
Hot Standby CPU Redundancy Features
For details on the configuration and operation of a Hot Standby CPU redundancy system, refer to the PACSystems
Hot Standby CPU Redundancy User’s Manual, GFK-2308.
? Supports single and redundant Ethernet remote I/O LANs through Ethernet Network Interface Unit (ENIU)
modules
? Supports simplex and redundantly controlled PROFINET remote IO (requires firmware version 8.00 or later)
? Survives any one single point of failure
? Bumpless switching
o Synchronized CPUs
o One scan switching
o Transfer data size up to 2Mbytes; selected in CPU hardware configuration and in variable properties
? Supports two redundancy communications links
? Online repair of failed component
? Online programming
? Redundancy Memory Xchange Module
o Manual toggle switch for role switching, which transitions control from the active unit to the backup unit
o Redundancy status LEDs
? Application-initiated role switching to switch the active unit to backup status
? Redundancy status bits and message logging
? Memory error checking and correction (ECC) single bit correcting and multiple bit checking
? Background diagnostics
HSB Control Strategy
The HSB control strategy has the following characteristics:
? Active unit does not automatically switch to primary on resynchronization
? Critical control data plus all redundant outputs must be included in the output data transfer
? Bumpless switchover from active unit to backup unit This product is intended for use with the RX3i system. Its components are considered open equipment (having live
electrical parts that may be accessible to users) and must be installed in an ultimate enclosure that is
manufactured to provide safety. At a minimum, the enclosure shall provide a degree of protection against solid
objects as small as 12mm (fingers, for example). This equates to a NEMA/UL Type 1 enclosure or an IEC60529 IP20
rating providing at least a pollution degree 2 environment. For details about installing RX3i rack systems, refer to
PACSystems RX3i System Manual, GFK-2314.
Installation in Hazardous Areas
The following information is for products bearing the UL marking for Hazardous Areas or ATEX marking for
explosive atmospheres:
CLASS 1 DIVISION 2 GROUPS ABCD
? This equipment is an open-type device and is meant to be installed in an enclosure suitable for the
environment that is only accessible with the use of a tool.
? Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous Locations, or nonhazardous locations
only.
? Warning – EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2.
? Warning – WHEN IN HAZARDOUS LOCATIONS, TURN OFF POWER BEFORE REPLACING OR WIRING
MODULES.
? Warning – EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NONHAZARDOUS.
ATEX Zone 2
This module must be mounted in an enclosure certified in accordance with EN60079-15 for use in Zone 2, Group IIC
and rated IP54. The enclosure shall only be able to be opened with the use of a tool.
